Dixon RB14, Boss™ Clamp, 4 Bolt Type, 2 Gripping Fingers, 1" Hose ID, 1-44/64"-1-60/64" Hose OD, Stainless Steel

Item # RB14

Ships in 3-5 Business Days

SUBJECT TO MANUFACTURER AVAILABILITY

Details

Details

RB14 | Boss Clamp 4 Bolt Type, 2 Gripping Fingers, Stainless Steel, 1" Hose Inside Diameter (I.D.), 1-60/64" Hose ID To, 1-44/64" Hose OD From, 21 ft. Lbs. Torque, Boss Series.
More Information
Weight 1.570000
Brand Dixon Valve & Coupling
Product Type Simple product
MPN RB14
Product Boss™ Clamps
Series Boss™
Material Stainless Steel
Hose ID To 1-60/64"
Hose OD From 1-44/64"
Application Bolts in Boss Clamps are designed to bend as they are tightened. This allows the clamp to conform to the hose outside diameter. Always tighten bolts to their specified torque valu. Periodic re-tightening of bolts is required due to "cold flow" phenomenon present in all rubber hoses. Boss Clamps are for single use only! Once removed they are to be discarded.
Features 4-bolt type clamp with 2 gripping fingers and 2 clamp sections
Specifications Recommended for steam service up to 450°F (232°C).
Data 21 ft. lbs. (torque)
Instructions
  • 4 Bolt Dixon Boss Clamp Bolt Tightening Sequence, Using a torque wrench, begin tightening the bolts as follows:
  • 1. Back bolt (bolt with nut facing assembler that is furthest away from gripping finger) 1 full turn
  • 2. Front bolt (bolt with nut facing assembler that is closest to gripping finger) 1 full turn
  • 3. Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued
  • 4. Opposite side back bolt (bolt with nut facing assembler furthest away from gripping finger) 1 full turn
  • 5. Opposite side front bolt (bolt with nut facing assembler closest to gripping finger) 1 full turn
  • 6. Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued
  • 7. Repeat above procedure "a" through "f" until all of the bolts have reached the recommended torque
  • 8. Remove assembly from vise
Safety Notes The bolts used in the Boss interlocking clamps are not standard bolts. They vary from standard bolts in their length, diameter, overall thread length and material hardness. These bolts can be retorqued, but it is not recommended that the bolts or clamps be reused, as they are designed for a single bend only. Dixon Recommends using only factory supplied replacement bolts. Replacement nuts and bolts are available, Contact Anderson Process for more information.Torque values for clamps are based on dry bolts. The use of lubricant on bolts will adversely effect clamp performance. Do not lubricate nuts and bolts. Recommended torque rating in ft. lbs. Worn-out hose couplings can be dangerous. They should be checked regularly and replace when necessary. Each coupling user should review applications and add safety devices where indicated. Pressurized steam is an extremely dangerous commodity. Only hose, fittings, clamps and accessory items that have been approved for steam service should ever be used! Never use an unapproved item for steam service. Always follow the manufacturer's product recommendations for pressurized steam handling.
WARNING! This product contains a chemical known to the State of California to cause birth defects or other reproductive harm. Do not use in connection with drinking water. Wash hands after handling. For more information go to www.P65Warnings.ca.gov

Related Documents

Reviews

Reviews

Write Your Own Review
You're reviewing:Dixon RB14, Boss™ Clamp, 4 Bolt Type, 2 Gripping Fingers, 1" Hose ID, 1-44/64"-1-60/64" Hose OD, Stainless Steel